Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 86

Page: 86 / 327

Safety instructions

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

87010285

Close the stop-cock (position 0) to secure the tailgate before carrying out work
beneath the lifted tailgate.

54106501

Adjust travelling height of hydraulic chassis via three-way cock:

(1)

Upper stop-cock to the right (open) = Right-hand vehicle side
preselected

Lower stop-cock down (open) = Right-hand vehicle side can be
lifted (max. 2 cm)

(2)

Upper stop-cock down (closed) and lower stop-cock to the right
(closed) = Travelling height cannot be changed

(3)

Upper stop-cock to the left (open) = Left-hand vehicle side
preselected

Lower stop-cock down (open) = Left-hand vehicle side can be
lifted (max. 2 cm)

(1)

(2)

(3)

87010288

This pictograph marks fixing points for lifting equipment (jack).

87006091

This pictograph marks lashing points for fixing lashing equipment when
transporting the machine.

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands

Strautmann Giga-Vitesse CFS 3602, Operating Instructions Manual

Search results

Summary of Contents for Giga-Vitesse CFS 3602

Reviews:

Related manuals for Giga-Vitesse CFS 3602

Brands by name

Popular brands