background image

Safety instructions

 

 

 

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO   03.18 

56 

 

 

Safety instructions 

 

 

This chapter provides important information for safety-conscious operation of the machine. 

 

 

3.1 

Correct use 

 

 

 

The forage wagon models "Giga Vitesse CFS / Giga Vitesse CFS DO" are exclusively intended for 
cutting, charging, transport and distribution of green and dried-out forage. 

Depending on the model, the maximum admissible speed is 40/60/62 km/h. Motorway journeys with a 
62 km/h model are only allowed in connection with ABS. 

Slopes can be travelled on as follows: 

• 

Traversing hills 

Direction of motion to the left  

 

23 degrees 

Direction of motion to the right  

 

23 degrees 

• 

Slope line 

Uphill  

 

 

 

 

23 degrees 

Downhill   

 

 

 

23 degrees 

The following is also part of the correct use: 

• 

The observance of all instructions contained herein, 

• 

the adherence to the inspection and maintenance work, 

• 

the exclusive use of original Strautmann spare parts. 

Any use beyond this is prohibited and will be regarded as incorrect. 

For any damage resulting from incorrect use 

• 

the user will be solely responsible, 

• 

B. Strautmann & Söhne GmbH u. Co. KG will not assume any liability. 

 

 

 

 

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews: