Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 81 | Manualshive

Page: 81 / 327

background image

Safety instructions

81

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

87010271

Risk to any part of the body of being crushed and/or risk of impact if people
stand within the hazardous area of the machine!

This risk may cause most serious injuries or even death.

People are not allowed within the hazardous area of the machine as long as the
tractor engine is running.

87010276

Risk to any part of the body of being drawn in or becoming entangled due to
powered working tools!

This risk may cause most serious injuries or even death.

•

Keep sufficient safe distance to powered working tools.

•

Ensure that people keep sufficient safe distance to powered working tools.

87010278

Risk of becoming entangled and wound up due to the powered propeller
shaft!

This risk may cause most serious injuries or even death.

•

Keep sufficient safe distance to the propeller shaft as long as the tractor
engine is running with the propeller shaft coupled / the hydraulic system
connected.

•

Ensure that people keep sufficient safe distance to the powered propeller
shaft.

87010279

Risk of cuts for fingers and hands due to working on sharp / sharp-edged
working tools!

This risk may cause most serious injuries including loss of limbs.

Observe the information in the operating instructions before carrying out work on
sharp working tools.

87010280

Risk to hands and arms of being drawn in or becoming entangled in moving
power transmission parts!

This risk may cause most serious injuries including loss of limbs.

Never open nor remove protective devices as long as the tractor engine is running
with the propeller shaft coupled/the hydraulic/electronic system connected.

«
...
79
80
81
82
83
...
»

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews:

No comments

Related manuals for Giga-Vitesse CFS 3602

Brand: Febco Pages: 12

Brand: Yetter Pages: 16

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Backyard Play Systems Pages: 64

Brand: Haenim Pages: 2

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: EarthQuake Pages: 28

Brand: TAIKO Audio Pages: 24

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands