Strautmann Giga-Vitesse CFS 3602 Operating Instructions Manual Download Page 139 | Manualshive

Page: 139 / 327

background image

Operation

139

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

6.1.3.3

Switch road travel mode off

With the road travel mode switched off:

•

the

Working

menu appears,

•

all functions of the control set are enabled,

•

the hydro-pneumatic drawbar suspension (optional extra), the
axle suspension of the hydro-pneumatic chassis and the
warning beacon (optional extra) are switched off,

•

the work lights (optional extra) are switched on if the work lights
were on when carrying out the function "Switch road travel
mode on".

1.

Press the

key again.

The road travel mode is switched off. The

Working

menu appears.

The screen shows:

«
...
137
138
139
140
141
...
»

Summary of Contents for Giga-Vitesse CFS 3602








































































































































































































































































































































Reviews:

No comments

Related manuals for Giga-Vitesse CFS 3602

Brand: OMCA Pages: 72

Brand: Barko Hydraulics Pages: 92

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Garmin Pages: 20

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Brand: EuroLite Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands