4-8
SERVICE MENU
MOTOR MENU
MOTOR MENU
AGING
AGING
SCAN
SCAN
NOW AGING
AGING
FEED
FEED
NOW AGING
AGING
BOTH
BOTH
NOW AGING
To stop Aging, press [ENTER] key. The print head carriage automatically moves back to the locked position,
then returns to this menu after being capped.
Make sure not to perform Aging for a long time when the machine is filled with ink in order to prevent the ink from
drying up. If ink filled, aging runs doing flushing. If ink not filled, aging runs without flushing.
SERVICE MENU
SERVO LOCK
SERVO LOCK
S:
100
SERVO LOCK
F:
152
SERVO LOCK
S:*
0
SERVO LOCK
F:*
0
This menu is to check if Servo Motor can be locked correctly.
While in this menu, Servo Motor becomes free. When the print head carriage is moved by hands, the corresponding value
will be displayed. If not, Servo Motor is not controlled correctly.
Pressing [ENTER] key locks Servo Motor.
If the print head carriage is locked when Servo Motor is locked, power control should be done correctly.
SERVICE MENU
HEATER MENU
HEATER MENU
SVC. MODE HEAT.
SVC. MODE HEAT.
STOP > STOP
SERVICE MENU
HEATER ADJUST
HEATER ADJUST
PRE-R
HEATER ADJUST
PRE-F
PRE-R
0
-3
PRE-F
0
-3
-5~+5
Default:0
-5~+5
Default:0
HEATER ADJUST
0
-3
-5~+5
Default:0
This menu is to offset heater temperature according to the actual temperature of the heater.
You can add +/- 5 degrees to the displayed temperature on the heater’s LCD.
Example : Actual temperature of the heater : 32 C, Heater LCD display : 37. You can 5 to keep the heater in 37 C.
HEATER ADJUST
DRYER A
DRYER A
0
-3
-5~+5
Default:0
HEATER ADJUST
DRYER B
DRYER B
0
-3
-5~+5
Default:0
HEATER ADJUST
DRYER C
DRYER C
0
-3
-5~+5
Default:0
SUB MENU
PORT CHECK
DETECTING...
00: 0B
Waiting data to be input
NETWORK
B3:1073741824B
Showing the data coming via network
This menu is to check the incoming data via network.
At the bottom row in LCD, Sum Check and the data size in bytes will be displayed.
Sum Check in 2 digits at left in hex system and data bytes in 10 digits at right in decimal system will be displayed.
To clear Sum Check and input data, press [ENTER] key.
SUB MENU
MAINTE. MSG.
MAINTE. MSG.
NONE 100 hours
This menu is to set time to show Maintenance Message. When printing time reaches the set time, Maintenance message appears.
This menu is to adjust Paper Side Sensor. Refer to [4-7 PAPER SIDE SENSOR ADJUSTMENT].
SUB MENU
PAPERSIDE SENS
PAPERSIDE SENS
OUTPUT LEVEL
PAPERSIDE SENS
SENSOR AUTOTEST
OUTPUT LEVEL
0.7V
NOW PROCESSING..
SENSOR AUTOTEST
0.5V NOISE 0
This is to set ON/OFF of heater while in Service Mode.
START : Heater ON, STOP : Heater OFF
Default : STOP
Default:NONE, 10~990 hours(every 10 hours)
SCAN : Aging for Scan Motor only.
Scan Motor runs right and left in max. printing width
together with the print head carriage.
FEED : Aging for Feed Motor only.
Feed Motor runs back and forth for 100mm.
BOTH : Aging for Scan Motor and Feed Motor.
Scan Motor runs right and left in max. printing width
together with the print head carriage, and Feed Motor
runs back and forth for 100mm.
Summary of Contents for Advanced Jet AJ-1000
