NXP Semiconductors PN7360AUEV User Manual Download | Manualshive

Page: 267 / 345

background image

NXP Semiconductors

UM10858

PN7462 family HW user manual

UM10858

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2018. All rights reserved.

User manual
COMPANY PUBLIC

Rev. 1.4 — 14 May 2018

314514

267 of 345

14.3.1.3 Configuring the I2C interface

The following parameters can be configured via the register
HOSTIF_I2C_CONTROL_REG (see

•

I2C slave address (2 LSBs)

•

High-speed mode (will select high speed mode of pads). Fast mode and standard

mode are both enabled by default

•

I2C soft reset enable

•

I2C Device ID enable

The Host Interface ensures that changes to these parameters will not take effect while
output from the Host Interface is BUSY (logic high).

14.3.1.4 Clock requirements

The I2C block uses the system clock to generate the request lines for data exchange.
The main I2C functionality is done with the clock supported via the SCL pin. Two 25 ns
filters are needed: one each for Start and Stop bit detection.

14.3.1.5 Transfer speed

The host interface supports Standard-mode (Sm), Fast-mode (Fm) and High-speed
mode (Hs-mode). Each mode is half-duplex only. The bitrate speeds for each mode are
listed in the following table.

Table 313. I2C Mode Maximum Bitrates

Mode

Max Bitrate

Standard-mode (Sm)

100 kbit/s

Fast-mode (Fm)

400 kbit/s

High-speed mode (Hs-mode)

3.4 Mbit/s

There is no difference in functionality between Standard-mode and Fast-mode; only the
frequency of SCL changes. To enable High-speed mode, set bit I2C_HS_ENABLE in
register HOSTIF_I2C_CONTROL_REG. With this bit set, the Host Interface responds
with an ACK to the slave address following the High-speed mode, Master Code and
Repeated Start sequence. In addition, the output port

is set logic high to drive the I2C

pads in the correct configuration. The I2C interface does not support clock stretching.

14.3.1.6 I2C address

The upper bits of the I2C slave address are hardcoded. The value corresponds to the
NXP identifier for I2C blocks. The value is 01010XXb. The lower two bits are defined via
field I2C_ADDR in register HOSTIF_I2C_CONTROL_REG. The 10-bit addressing is not
supported.

14.3.1.7 ACK/NACK behavior

The following sections describe the conditions under which the I2C block generates a
NACK/ACK.

Host write to I2C:

The slave W will be ACKed provided that:

•

Selected host interface is I2C

«
...
265
266
267
268
269
...
»

Summary of Contents for PN7360AUEV


























































































































































































































































































































































Reviews:

No comments

Related manuals for PN7360AUEV

Brand: iCeeO2 Pages: 7

Brand: Parasound Pages: 72

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: e-BLEACH Pages: 24

Brand: Eaton Pages: 4

Brand: 2N Pages: 107

Micro850 series

Brand: Allen-Bradley Pages: 24

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

Brand: IDTECK Pages: 51

Brand: YASKAWA Pages: 360

Brand: Velleman Pages: 22

Brand: National Instruments Pages: 27

Brand: Evco Pages: 78

Brand: Meilhaus Electronic Pages: 19

RailBoss 4 Basic

Brand: G-Scale Graphics Pages: 22

Brand: Interactive Technologies Pages: 431

Brand: A.O. Smith Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands