NXP Semiconductors PN7360AUEV User Manual Download

Page: 261 / 345

NXP Semiconductors

UM10858

PN7462 family HW user manual

UM10858

All information provided in this document is subject to legal disclaimers.

User manual
COMPANY PUBLIC

Rev. 1.4 — 14 May 2018

314514

261 of 345

14.2.9.8 SPIM_CRC_STATUS_REG

This register reflects the RX/TX CRC values.

Table 302. SPIM_CRC_STATUS_REG (address offset 0x001C)

Bit

Symbol

Access Reset

Value

Description

31:16

RESERVED

Reserved

15:8

CRC_TX_VAL

0xFF

Value of internal TX CRC

7:0

CRC_RX_VAL

0xFF

Value of internal RX CRC

14.2.9.9 SPIM_WATERLEVEL_REG

This register is used to indicate the water level.

Table 303. SPIM_WATERLEVEL_REG (address offset 0x0020)

Bit

Symbol

Access Reset

Value

Description

31:9

RESERVED

Reserved

8:0

WATERLEVEL

R/W

Number of bytes received in
incoming frame, or sent in out
coming frame before triggering an
interrupt.

If set to 0, this feature is disabled.

14.2.9.10 SPIM_BUFFER_MAPPING_REG

REGION_SIZE – Size of buffer region in system RAM. 0x1FFF (8K) is the current RAM
size in PN7462 family. Note that software need to initialize REGION_SIZE <= 0x1FFF
always before using the Buffer.

Table 304. SPIM_BUFFER_MAPPING_REG (address offset 0x002C)

Bit

Symbol

Access Reset

Value

Description

31:30

RESERVED

Reserved

29:16

REGION_START_ADDR

R/W

Start address of buffer region in
system RAM.

Any AHB transaction address would
be 0x00100000 (RAM address for
PN7462 family) +
REGION_START_ADDR.

Also REGION_START_ADDR must
be less than or equal to
REGION_SIZE.

15:14

RESERVED

Reserved

13:0

REGION_SIZE

R/W

0x2FFF

Size of buffer region in system RAM
0x2FFF is the Current RAM Size in
PN7462 family

Summary of Contents for PN7360AUEV


























































































































































































































































































































































Search results

Summary of Contents for PN7360AUEV

Reviews:

Related manuals for PN7360AUEV

Brands by name

Popular brands

NXP Semiconductors PN7360AUEV, User Manual

Search results

Summary of Contents for PN7360AUEV

Reviews:

Related manuals for PN7360AUEV

Brands by name

Popular brands