Mitsubishi Electric M32170F3VFP User Manual Download

Page: 526 / 850

11-28

Ver.0.10

(1) ADnCMSL (A-Dn scan mode selection) bit (D1)

This bit selects scan mode of the A-Dn converter between single-shot scan and continuous scan.

Setting this bit to 0 selects single-shot scan mode, so that the channels selected by the

ANnSCAN (scan loop selection) bits are sequentially A-D converted and when A-D conversion in

all selected channels are completed, the conversion operation stops.

Setting this bit to 1 selects continuous scan mode, so that when operation in single-shot scan

mode is completed, the selected channels are A-D converted beginning with the first channel

again. This A-D conversion is continued until halted by setting the ADnCSTP (A-Dn conversion

stop) bit to 1.

(2) ADnCTRG (A-Dn hardware trigger selection) bit (D2)

When starting A-D conversion of the A-Dn converter in hardware, this bit selects whether to use

external ADTRG signal input or MJT output (output event bus 3 for A-D0, or TID1 overflow/

underflow for A-D1) to start the operation. The content of this bit is ignored when the ADnSSEL

(A-Dn conversion start trigger selection) bit is set to choose a software trigger. When using the

____________

ADTRG pin for a start trigger, not that if A-D conversion is completed while the ADTRG pin input

is held low, new A-D conversion is not started.

(3) ADnCSEL (A-Dn conversion start trigger selection) bit (D3)

This bit selects whether to use a software or hardware trigger to start A-D conversion of the A-Dn

converter during scan mode. When you choose a software trigger, A-D conversion is started by

setting the ADnCSTT (A-Dn conversion start) bit to 1. When you choose a hardware trigger, A-D

conversion is started for the cause of start selected by the ADnCTRG (hardware trigger

selection) bit.

(4) ADnCREQ (A-Dn interrupt request/DMA transfer request selection) bit (D4)

For the A-D0 converter (AD0SCM0), this bit selects whether to request an A-D0 conversion

interrupt or DMA transfer when one cycle of scan operation is completed. For the A-D1 converter

(AD1SCM0), this bit selects whether to enable or disable an A-D0 conversion interrupt when one

cycle of scan operation is completed.

(5) ADnCCMP (A-Dn conversion completion) bit (D5)

This is a read-only bit, which when reset is 1. This bit is 0 when the A-Dn converter is performing

scan mode A-D conversion and set to 1 when single-shot scan mode is completed, or when

continuous scan mode is halted by setting ADnCSTT (A-Dn conversion stop) bit to 1.

A-D CONVERTERS

11.2 A-D Converter Related Registers

Summary of Contents for M32170F3VFP



















































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for M32170F3VFP

Reviews:

Related manuals for M32170F3VFP

Brands by name

Popular brands

Mitsubishi Electric M32170F3VFP, User Manual

Search results

Summary of Contents for M32170F3VFP

Reviews:

Related manuals for M32170F3VFP

Brands by name

Popular brands