Mitsubishi Electric M32170F3VFP User Manual Download Page 22

Page: 22 / 850

1-4

Ver.0.10

OVERVIEW

1.1 Outline of the 32170

1.1.4 Built-in Clock Frequency Multiplier

• The 32170 internally multiplies the input clock signal frequency by 4 and the internal peripheral

clock by 2. If the input clock frequency is 10.0 MHz, the CPU clock frequency will be 40 MHz

and the internal clock frequency 20 MHz.

1.1.5 Built-in Powerful Peripheral Functions

(1) Built-in multijunction timer (MJT)

• The multijunction timer is configured with the following timers:

➀

16-bit output-related timer

35 channels

➁

16-bit input/output-related timer

10 channels

➂

16-bit input-related timer

11 channels (incorporating three channels of multiply-by-4

counter)

➃

32-bit input-related timer

8 channels

Each timer has multiple modes of operation, which can be selected according of the purpose of use.

• The multijunction timer has internal clock bus, input event bus, and output event bus, allowing

multiple timers to be combined for use internally. This provides a flexible way to make use of

timer functions.

• The output-related timers (TOP) have a correction function. This function allows the timer's

count value in progress to be increased or reduced as desired, thus materializing real-time

output control.

(2) Built-in 10-channel DMA

• The 10-channel DMA is built-in, supporting data transfers between internal peripheral I/Os or

between internal peripheral I/O and internal RAM. Not only can DMA transfer requests be

generated in software, but can also be triggered by a signal generated by an internal

peripheral I/O (e.g., A-D converter, MJT, or serial I/O).

• Cascaded connection between DMA channels (DMA transfer in a channel is started by

completion of transfer in another) is also supported, allowing for high-speed transfer

processing without imposing any extra load on the CPU.

(3) Built-in 16-channel A-D converters

• The 32170 contains two 16-channel A-D converters which can convert data in 10-bit

resolution. In addition to single A-D conversion in each channel, successive A-D conversion in

four, eight, or 16 channels combined into one unit is possible.

• In addition to ordinary A-D conversion, a comparator mode is supported in which the A-D

conversion result is compared with a given set value to determine the relative magnitudes of

two quantities.

• When A-D conversion is completed, the 32170 can generate not only an interrupt, but can also

generate a DMA transfer request.

• The 32170 supports two read out modes, so that A-D conversion results can be read out in 8

bits or 10 bits.

Summary of Contents for M32170F3VFP



















































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for M32170F3VFP

Reviews:

Related manuals for M32170F3VFP

Brands by name

Popular brands

Mitsubishi Electric M32170F3VFP, User Manual

Search results

Summary of Contents for M32170F3VFP

Reviews:

Related manuals for M32170F3VFP

Brands by name

Popular brands