Appendix 1 Explanation of Parameters
MITSUBISHI CNC
218
【
#11033(PR)
】
skipB_no_sens Unconnected sensor selection when skip is set to contact B
Select the contact of the sensor which you wish to set as unconnected, when the skip signal is set to
contact B.
Set "1" for the contact to be unconnected.
bit0: Skip input 1
bit1: Skip input 2
bit2: Skip input 3
bit3: Skip input 4
(Note 1)This parameter is enabled when "#1258 set30/bit0" is set to "1".
(Note 2)bit4 to bit7 are not used. Set to "0".
(Note 3)This parameter is independent of PLC skip.
---Setting range---
00000000 to 00001111 (Binary)
【
#12015(PR)
】
v_dist Hypothetical axis tool length
In the hypothetical linear axis control, set the length in the hypothetical plane from the rotation center
of the actual rotary axis to the tool center.
Setting "0" disables the hypothetical axis.
---Setting range---
0 to 99999.999 (mm)
【
#12016(PR)
】
v_ori Hypothetical axis machine zero point
Set the distance Xs from the hypothetical axis machine zero point to the center of the rotary axis. If
the rotation center is left side from the zero point as follows, set a negative value.
---Setting range---
-99999.999 to 99999.999 (mm)
【
#12017(PR)
】
ofsang Actual rotary axis compensation angle
Set the angle Co of the vector from the rotation center to the tool when the C-axis (actual axis) is
positioned at 0 degrees with respect to the positive direction of the hypothetical axis (X-axis) in the
hypothetic plane.
---Setting range---
0 to 359.999(°)
X
S
-X
S
Rotation
center
Rotation
center
Tool
Tool
Hypothetical axis
machine zero point
Hypothetical machine
X-axis coordinate
Actual machine coordinate
Y-axis
Machine
zero point
Tool
Compensation
angle Co
X-axis
positive direction
C-axis rotation center
Hypothetical machine
coordinate X-axis
Summary of Contents for C70
