Appendix 1 Explanation of Parameters
MITSUBISHI CNC
170
Appendix 1.2 Machining Parameters
The parameters with "(PR)" requires the CNC to be turned OFF after the settings. Turn the power OFF and ON to enable
the parameter settings.
【
#8001
】
WRK COUNT M
Set the M code for counting the number of the workpiece repeated machining.
The number of the M-codes set by this parameter is counted.
The No. will not be counted when set to "0".
---Setting range---
0 to 99
【
#8002
】
WRK COUNT
Set the initial value of the number of workpiece machining. The number of current workpiece
machining is displayed.
---Setting range---
0 to 999999
【
#8003
】
WRK COUNT LIMIT
Set the maximum number of workpiece machining.
A signal will be output to PLC when the number of machining times is counted to this limit.
---Setting range---
0 to 999999
【
#8004
】
SPEED
Set the feedrate during automatic tool length measurement.
---Setting range---
1 to 1000000 (mm/min)
【
#8005
】
ZONE r
Set the distance between the measurement point and deceleration start point.
---Setting range---
0 to 99999.999 (mm)
【
#8006
】
ZONE d
Set the tolerable range of the measurement point.
An alarm will occur when the sensor signal turns ON before the range, set by this parameter, has not
been reached from the measurement point, or when the signal does not turn ON after the range is
passed.
---Setting range---
0 to 99999.999 (mm)
【
#8007
】
OVERRIDE
Set the override value for automatic corner override.
---Setting range---
0 to 100 (%)
【
#8008
】
MAX ANGLE
Set the maximum corner opening angle where deceleration should start automatically.
When the angle is larger than this value, deceleration will not start.
---Setting range---
0 to 180 (°)
Summary of Contents for C70
