Mitsubishi Electric A800 Plus Series, Function Manual

Page: 30 / 242

Parameter list (by parameter number)
PARAMETER LIST
29
2
1293 R515 Data table taper ratio 3 0 to 100% 0.1% 0%
92 ,
124
1294 R516 Data table winding diameter 4 0 to 6553 mm, 9999 1 mm 9999
92 ,
124
1295 R517 Data table taper ratio 4 0 to 100% 0.1% 0%
92 ,
124
1296 R518 Data table winding diameter 5 0 to 6553 mm, 9999 1 mm 9999
92 ,
124
1297 R519 Data table taper ratio 5 0 to 100% 0.1% 0%
92 ,
124
1298 R007
Stored winding length (upper 4
digits)
0 to 9999(m
∗12
) 1(m
∗12
) 0(m
∗12
) 176
1299 R008
Stored winding length
increment
0 to 2 1 0 176
1300
to
1343
N500
to
N543
Communication option parameters. For details, refer to the Instruction Manual of the option.
1346 R424
Winding length detection (upper
4 digits)
0 to 9999(m
∗12
) 1(m
∗12
) 0(m
∗12
) 176
1348 G263
P/PI control switchover
frequency
0 to 400 Hz 0.01 Hz 0 Hz ─
∗17
1349 G264
Emergency stop operation
selection
0, 1, 10, 11 1 0 ─
∗17
1350
to
1359
N550
to
N559
Communication option parameters. For details, refer to the Instruction Manual of the option.
1401 R301 Tension command increment 0 to 2 1 0 118
1402 R310
Tension command input voltage
bias
0 to 100% 0.1% 0% 118
1403 R311 Tension command bias 0 to 100 N
∗13
0.01 N
∗13
0 N 118
1404 R312
Tension command input voltage
gain
0 to 100% 0.1% 100% 118
1405 R313 Tension command gain 0 to 100 N
∗13
0.01 N
∗13
100 N
∗13
118
1406 R340
Commanded tension reduction
scaling factor during stall
condition
0 to 200% 0.1% 20% 137
1407 R341
Speed limit during stall
condition
0 to 60 Hz 0.01 Hz 1 Hz 137
1409 R343
Tension command cushion time
during stall condition
0 to 360 s, 9999 0.01 s 9999 137
1410 R530 Motor inertia
0 to 500 kg·m
2
, 9999 0.01 kg·m
2
0 kg·m
2
130
1411 R531 Empty reel inertia
0 to 500 kg·m
2
, 9999 0.01 kg·m
2
0 kg·m
2
130
1412 R532 Roll width 0 to 5000 mm 1 mm 0 mm 130
1413 R533 Material specific gravity
0 to 20 g/cm
3
0.001 g/cm
3
0 g/cm
3
130
1414 R535
First acceleration time for inertia
compensation
0 to 3600 s 0.1 s 15 s 130
1415 R536
First deceleration time for inertia
compensation
0 to 3600 s 0.1 s 15 s 130
1418 R534
Inertia compensation cushion
time
0 to 360 s 0.01 s 0 s 130
1419 R550
Mechanical loss setting
frequency bias
900 to 1100% 0.1% 1000% 135
1420 R551
Mechanical loss setting
frequency 1
0 to 400 Hz, 9999 0.01 Hz 9999 135
1421 R552 Mechanical loss 1 900 to 1100% 0.1% 1000% 135
1422 R553
Mechanical loss setting
frequency 2
0 to 400 Hz, 9999 0.01 Hz 9999 135
1423 R554 Mechanical loss 2 900 to 1100% 0.1% 1000% 135
1424 R555
Mechanical loss setting
frequency 3
0 to 400 Hz, 9999 0.01 Hz 9999 135
1425 R556 Mechanical loss 3 900 to 1100% 0.1% 1000% 135
1426 R557
Mechanical loss setting
frequency 4
0 to 400 Hz, 9999 0.01 Hz 9999 135
1427 R558 Mechanical loss 4 900 to 1100% 0.1% 1000% 135
Pr.
Pr.
group
Name Setting range
Minimum
setting
increments
Initial value Refer
to
page
Customer
setting FM CA