Mitsubishi Electric A800 Plus Series, Function Manual

Page: 23 / 242

Parameter list (by parameter number)
22
PARAMETER LIST
774 M101
Operation panel monitor
selection 1
1 to 3, 5 to 14, 17 to 20, 22
to 36, 38, 40 to 46, 50 to
57, 61 to 64, 67, 71 to 74,
81 to 93, 97, 98, 100,
9999
1 9999 181
775 M102
Operation panel monitor
selection 2
1 9999 181
776 M103
Operation panel monitor
selection 3
1 9999 181
778
A682
4 mA input check filter 0 to 10 s 0.01 s 0 s ─
∗17
T054
799 M520
Pulse increment setting for
output power
0.1, 1, 10, 100, 1000 kWh 0.1 kWh 1 kWh ─
∗17
800 G200 Control method selection
0 to 2, 9 to 12, 20,
100 to 102, 109 to 112
1 20 5
801 H704 Output limit level 0 to 400%, 9999 0.1% 9999 ─
∗17
802 G102 Pre-excitation selection 0, 1 1 0 ─
∗17
803 G210
Constant output range torque
characteristic selection
0 to 2, 10, 11 1 0 ─
∗17
804
R300
Tension / Torque command
source selection
0 to 6 1 0 118
D400
805 D401 Torque command value (RAM) 600 to 1400% 1% 1000% ─
∗17
806 D402
Torque command value
(RAM,EEPROM)
600 to 1400% 1% 1000% ─
∗17
807 H410 Speed limit selection 0 to 2 1 0 ─
∗17
808 H411
Forward rotation speed limit/
speed limit
0 to 400 Hz 0.01 Hz 60 Hz 50 Hz ─
∗17
809 H412
Reverse rotation speed limit/
reverse-side speed limit
0 to 400 Hz, 9999 0.01 Hz 9999 ─
∗17
810 H700
Torque limit input method
selection
0 to 2 1 0 ─
∗17
811 D030 Set resolution switchover 0, 1, 10, 11 1 0 ─
∗17
812 H701 Torque limit level (regeneration) 0 to 400%, 9999 0.1% 9999 ─
∗17
813 H702 Torque limit level (3rd quadrant) 0 to 400%, 9999 0.1% 9999 ─
∗17
814 H703 Torque limit level (4th quadrant) 0 to 400%, 9999 0.1% 9999 ─
∗17
815 H710 Torque limit level 2 0 to 400%, 9999 0.1% 9999 ─
∗17
816 H720
Torque limit level during
acceleration
0 to 400%, 9999 0.1% 9999 ─
∗17
817 H721
Torque limit level during
deceleration
0 to 400%, 9999 0.1% 9999 ─
∗17
818 C112
Easy gain tuning response level
setting
1 to 15 1 2 ─
∗17
819 C113 Easy gain tuning selection 0 to 2 1 0 ─
∗17
820 G211 Speed control P gain 1 0 to 1000% 1% 60% ─
∗17
821 G212 Speed control integral time 1 0 to 20 s 0.001 s 0.333 s ─
∗17
822 T003 Speed setting filter 1 0 to 5 s, 9999 0.001 s 9999 ─
∗17
823
∗9
G215 Speed detection filter 1 0 to 0.1 s 0.001 s 0.001 s ─
∗17
824 G213
Torque control P gain 1 (current
loop proportional gain)
0 to 500% 1% 100% ─
∗17
825 G214
Torque control integral time 1
(current loop integral time)
0 to 500 ms 0.1 ms 5 ms ─
∗17
826 T004 Torque setting filter 1 0 to 5 s, 9999 0.001 s 9999 ─
∗17
827 G216 Torque detection filter 1 0 to 0.1 s 0.001 s 0 s ─
∗17
828 G224 Model speed control gain 0 to 1000% 1% 60% ─
∗17
829 R504
Taper ratio setting input filter
time constant
0 to 5 s 0.01 s 0.02 s 124
830 G311 Speed control P gain 2 0 to 1000%, 9999 1% 9999 ─
∗17
831 G312 Speed control integral time 2 0 to 20 s, 9999 0.001 s 9999 ─
∗17
832 T005 Speed setting filter 2 0 to 5 s, 9999 0.001 s 9999 ─
∗17
833
∗9
G315 Speed detection filter 2 0 to 0.1 s, 9999 0.001 s 9999 ─
∗17
834 G313 Torque control P gain 2 0 to 500%, 9999 1% 9999 ─
∗17
835 G314 Torque control integral time 2 0 to 500 ms, 9999 0.1 ms 9999 ─
∗17
836 T006 Torque setting filter 2 0 to 5 s, 9999 0.001 s 9999 ─
∗17
837 G316 Torque detection filter 2 0 to 0.1 s, 9999 0.001 s 9999 ─
∗17
840 G230 Torque bias selection 0 to 3, 24, 25, 9999 1 9999 ─
∗17
841 G231 Torque bias 1 600 to 1400%, 9999 1% 9999 ─
∗17
Pr.
Pr.
group
Name Setting range
Minimum
setting
increments
Initial value Refer
to
page
Customer
setting FM CA