Mitsubishi Electric A800 Plus Series, Function Manual

Page: 20 / 242

Parameter list (by parameter number)
PARAMETER LIST
19
2
475 R124 Third PID differential time 0.01 to 10 s, 9999 0.01 s 9999 86
476 R125
Third PID proportional band for
values below set point
0.1 to 1000%, 9999 0.1% 9999 86
477 R126
Third PID integral time for
values below set point
0.1 to 3600 s, 9999 0.1 s 9999 86
478 R127
Third PID differential time for
values below set point
0.01 to 10 s, 9999 0.01 s 9999 86
479 R128 Fourth PID proportional band 0.1 to 1000%, 9999 0.1% 9999 86
480 R129 Fourth PID integral time 0.1 to 3600 s, 9999 0.1 s 9999 86
481 R130 Fourth PID differential time 0.01 to 10 s, 9999 0.01 s 9999 86
482 R131
Fourth PID proportional band for
values below set point
0.1 to 1000%, 9999 0.1% 9999 86
483 R132
Fourth PID integral time for
values below set point
0.1 to 3600 s, 9999 0.1 s 9999 86
484 R133
Fourth PID differential time for
values below set point
0.01 to 10 s, 9999 0.01 s 9999 86
485 R149 Integral control activation 0 to 3 1 0 85
486 R140 Deviation A 400.1 to 600% 0.1% 600% 86
487 R141 Deviation B 400 to 599.9% 0.1% 400% 86
488 R142 Deviation C1 400.1 to 599.9%, 9999 0.1% 9999 86
489 R143 Deviation C2 400.1 to 599.9%, 9999 0.1% 9999 86
490 R144 PID gain A 0.1 to 1000%, 9999 0.1% 9999 86
491 R145 PID gain B 0.1 to 1000%, 9999 0.1% 9999 86
492 R146 PID gain C1 0.1 to 1000%, 9999 0.1% 9999 86
493 R147 PID gain C2 0.1 to 1000%, 9999 0.1% 9999 86
494 R148 PID gain D 0.1 to 1000%, 9999 0.1% 9999 86
495 M500 Remote output selection 0, 1, 10, 11 1 0 ─
∗17
496 M501 Remote output data 1 0 to 4095 1 0 ─
∗17
497 M502 Remote output data 2 0 to 4095 1 0 ─
∗17
498 A804
PLC function flash memory
clear
0, 9696 (0 to 9999) 1 0 ─
∗17
502 N013
Stop mode selection at
communication error
0 to 2, 11, 12 1 0 ─
∗17
503 E710 Maintenance timer 1 0 (1 to 9998) 1 0 ─
∗17
504 E711
Maintenance timer 1 warning
output set time
0 to 9998, 9999 1 9999 ─
∗17
505 M001 Speed setting reference 1 to 590 Hz 0.01 Hz 60 Hz 50 Hz ─
∗17
516 F400
S-pattern time at a start of
acceleration
0.1 to 2.5 s 0.1 s 0.1 s ─
∗17
517 F401
S-pattern time at a completion of
acceleration
0.1 to 2.5 s 0.1 s 0.1 s ─
∗17
518 F402
S-pattern time at a start of
deceleration
0.1 to 2.5 s 0.1 s 0.1 s ─
∗17
519 F403
S-pattern time at a completion of
deceleration
0.1 to 2.5 s 0.1 s 0.1 s ─
∗17
539 N002
MODBUS RTU communication
check time interval
0 to 999.8 s, 9999 0.1 s 9999 ─
∗17
547 N040
USB communication station
number
0 to 31 1 0 ─
∗17
548 N041
USB communication check time
interval
0 to 999.8 s, 9999 0.1 s 9999 ─
∗17
549 N000 Protocol selection 0, 1 1 0 ─
∗17
550 D012
NET mode operation command
source selection
0, 1, 9999 1 9999 ─
∗17
551 D013
PU mode operation command
source selection
1 to 3, 9999 1 9999 ─
∗17
552 H429 Frequency jump range 0 to 30 Hz, 9999 0.01 Hz 9999 ─
∗17
553 A603 PID deviation limit 0.0 to 100.0%, 9999 0.1% 9999 ─
∗17
554 A604 PID signal operation selection 0 to 3 1 0 76
555 E720 Current average time 0.1 to 1 s 0.1 s 1 s ─
∗17
556 E721 Data output mask time 0 to 20 s 0.1 s 0 s ─
∗17
557 E722
Current average value monitor
signal output reference current
0 to 500 A
∗2
0.01 A
∗2
Inverter rated
current
─
∗17
0 to 3600 A
∗3
0.1 A
∗3
560 A712 Second frequency search gain 0 to 32767, 9999 1 9999 ─
∗17
561 H020 PTC thermistor protection level 0.5 to 30 k Ω , 9999 0.01 k Ω 9999 ─
∗17
Pr.
Pr.
group
Name Setting range
Minimum
setting
increments
Initial value Refer
to
page
Customer
setting FM CA