Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 116

Page: 116 / 366

Software

Symptom

Possible Cause

Corrective Action

Unable to log

in to the EX

Controller Web

GUI using

the

mimx

user account

credentials

after it is reset

in Server

Manager.

Password

mismatch.Theminimum

number of characters

the Server Manager

accepts for the

password is seven.

However, if you reset

the password to a

seven-character

password, it is not

synchronized with the

mimx user account

because the mimx

and the SNMPv3

passwords require

a minimum of eight

characters.

Displaying the active mimx password

Start SSH client.

machine through an SSH session.

Execute the following command:

cd /

usr/libexec/mimx

Execute the following commands:

./mimxservermgt.sh -p./

mivbservermgt.sh -p

Executing these commands displays the

entries in the mimx and MiVoice Business

database, including all passwords.

Cannot log in

to the System

Administration

Tool for the

3300 ICP

Controller.

Forgot the login

credentials

See

Reset the System Admin Password

The MiVoice

Business

software is

unable to boot

from the HDD

(or SSD).

Partial or complete

disk corruption or disk

failure

You must recover the MiVoice Business

software from the HDD (or SSD). See

Unable to boot the MiVoice Business

System on 3300 ICP Controller

Document Version 1.0
Troubleshooting Guide

110

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands