manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

The Mitel MiVoice Business 3300 ICP Troubleshooting Manual is an essential resource for users of this versatile business communication system. Download this comprehensive manual for free from our website and discover in-depth troubleshooting advice to maximize the performance and efficiency of your telecommunications infrastructure.

Share
Download
background image

Diagnosing Problems

3.

Press 

Yes

 , and then press 

No

 until DHCP Trace? appears.

4.

Press 

Yes

 , and press the Up/Down volume keys to view the results of the DHCP

trace.

5.

To exit, do one of the following:

•

When you return to DHCP TRACE?, press 

No

 .

•

To return to the default display, press 

 Superkey

.

Configuring Video Conferencing Parameters

To configure video conferencing on the 5220 IP Phone (Dual Boot):

1.

Access the Configuration Menu (see 

Access Configuration Menu on Single Mode IP

Phones

).

2.

Press 

No

 until TOOLS AND FEATURES? appears.

3.

Press 

Yes

 and then press 

No

 until VIDEO CONFIGURATION? appears.

4.

Press 

Yes

 . VIEW PARAMETERS? appears.

5.

Do one of the following:

•

Press 

Yes

 and then follow the prompts. When you return to VIEW PARAMETERS?,

press 

No

 . MODIFY PARAMETERS appears.

•

To continue, press 

No

 . MODIFY PARAMETERS appears.

6.

Do one of the following:

•

Press 

Yes

 and follow the prompts to modify the video conferencing parameters,

store the changes, and reboot the phone.

•

To set the factory default settings, press Default and follow the prompts to set and

store the factory defaults and reboot the phone.

7.

To exit the current menu without a reboot:

•

To return to the main menu, press 

Yes

 at EXIT MENU?

•

To return to the default display, press 

Superkey

 .

Restoring Factory Default Settings

1.

Access the Configuration Menu (see 

Access Configuration Menu on Single Mode IP

Phones

).

2.

Press 

No

 until TOOLS AND FEATURES? appears.

3.

Press 

Yes

 and then press 

No

 until RESTORE DEFAULTS? appears.

4.

Press 

Yes

 and then follow the prompts to set and store the factory defaults and reboot

the phone.

Document Version 1.0

297

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVoice Business 3300 ICP

iDance XD200 Instruction Manual preview
XD200
Brand: iDance Pages: 25
Audipack VCL-1UP Installation Manual preview
VCL-1UP
Brand: Audipack Pages: 12
Grundig Varixx UMS 4401 SPCD Manual preview
Varixx UMS 4401 SPCD
Brand: Grundig Pages: 47
H2flow levelsmart User Instruction Manual preview
levelsmart
Brand: H2flow Pages: 16
Scott I-WXH 80 Instruction Manual preview
I-WXH 80
Brand: Scott Pages: 13
T+A DD 820 M User Manual preview
DD 820 M
Brand: T+A Pages: 70
JiangYi JY-8000N Instruction Manual preview
JY-8000N
Brand: JiangYi Pages: 13
Leviton Lumina LU20S-DNW Installation Instructions preview
Lumina LU20S-DNW
Brand: Leviton Pages: 3
Woodward 9907-026 Product Manual preview
9907-026
Brand: Woodward Pages: 32
RCA RS2217I User Manual preview
RS2217I
Brand: RCA Pages: 35
Emerson NR101TT Owner'S Manual preview
NR101TT
Brand: Emerson Pages: 16
Emerson Research iS133 Owner'S Manual preview
Research iS133
Brand: Emerson Pages: 2
Emerson PD6511 Owner'S Manual preview
PD6511
Brand: Emerson Pages: 8
Emerson MS9923TT Owner'S Manual preview
MS9923TT
Brand: Emerson Pages: 28
Emerson MS9933TT Owner'S Manual preview
MS9933TT
Brand: Emerson Pages: 36
Emerson MS9920 Owner'S Manual preview
MS9920
Brand: Emerson Pages: 14
Emerson RS1008 Owner'S Manual preview
RS1008
Brand: Emerson Pages: 31
Emerson MS9903TT Owner'S Manual preview
MS9903TT
Brand: Emerson Pages: 31

Brands by name

Popular brands

Load more brands