Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 192

Page: 192 / 366

Trunking

Symptom

Probable Cause

Corrective Action

•

Ensure that the PBX Number

field in the IP/XNET Trunk

Groups form contains a System

number which is programmed

correctly on the Local PBX:

•

The outgoing signaling DID

number at the Local PBX

must match the correct remote

incoming list.

•

The outgoing voice DID

number at the Local PBX

must match the correct remote

incoming list.

•

Interconnect restrictions must

be set up incorrectly in the

IP/XNET Trunk Profiles form

on the Local PBX (the profile

number must agree with the

correct remote profile number,

and must have the correct

profile setting).

Trunks Out-of-Service

Check trunk status

Trunk congestion

•

Check that no trunks are Out-of-

Service or MAN-BUSIED.

•

Ensure you have enough trunks

allocated for the expected call

rate.

•

Wait till more trunks become

available.

Outgoing calls fail

with reorder tone

(outbound side).

Invalid Dialing

Verify that the dialled numbers are

routeable.

Document Version 1.0
Troubleshooting Guide

186

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands