Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 59

Page: 59 / 366

Hardware

Symptom Probable Cause

Corrective Action

The serial

port on the

3300 ICP

controller is

unresponsive

while trying

to access

it using a

terminal

emulator

application.

•

Configuration

issue with the

terminal emulator

application.

•

Configuration issue

with the terminal

server, if the serial

port is connected

to the terminal

server (for example

LanTronix- SLC32).

•

Hardware issue.

Ensure that the terminal emulator application

connected to the controller's serial port through

the DB9 serial cable is configured correctly as

shown in the following figure.

If you have modified the default baud

rate (9600), then set the baud rate to

the recommended default value. See

Maintenance> Modify Default Baud Rate of

the System Console (3300 ICP Controller)

the

Technician's Handbook

If you are using a terminal server (for

example, LANTronix SLC32) to access your

controller's serial port remotely over the

network, then verify that:

•

the terminal emulator application has the

correct terminal server's port and protocol

configured.

•

the terminal server port is configured

correctly.

Run the terminal server's configuration

command for the terminal server port

connected to the controller's serial port with the

correct configuration values.

•

Service Units

on page 54

Document Version 1.0

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands