Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 169

Page: 169 / 366

Trunking

This chapter contains the following sections:

•

•

•

•

•

IP Trunking (IP Networking)

•

SIP Trunking

Trunk Troubleshooting Tips

•

If all the circuits supported by a module or card are out of service, it is likely defective. If

possible, swap the module or card with a known working module or card to confirm.

•

For help with diagnosing digital trunk problems, see

Trunks

•

In the System Administration Tool, use the

•

Line Quality Measurement Tool to test Loop Start Trunks that are connected to the AX

Controller Card Chassis, Analog Main Board, Analog Option Board, or ASU II.

•

Voice Quality Statistics form in combination with NetAlly (must be purchased separately)

to identify voice quality problems and performance trends for IP phones.

Document Version 1.0
Troubleshooting Guide

163

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands