Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 255

Page: 255 / 366

Voice Networking

Table 49: Troubleshooting Sharing Operations

Symptom

Possible Cause

Corrective Action

Unable to initiate sync

following an MiVoice

Business software

upgrade/ downgrade. Sync

button is grayed out.

Browser cache contains

stale Sys Admin Tool data

which is preventing the

sync from working.

Clear the browser cache.

In Internet Explorer: press

CTRL+SHIFT+DEL,

select Temporary Internet

Files, and clear Preserve

Favorites website data

Leave other check boxes

cleared, and then click OK.

In Firefox: press CTRL

+SHIFT+DEL, select

Everything for "Time range

to clear" and Cache, then

click OK.

In Chrome: press CTRL

+SHIFT+DEL, select the

beginning of time

next to

Clear the following items

from

and

Cached images

and files

, then click

Clear

Browsing Data

- In Edge: press CTRL

+SHIFT+DEL, select

Cached data and files

and then click

Clear

Document Version 1.0

249

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands