manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

The Mitel MiVoice Business 3300 ICP Troubleshooting Manual is an essential resource for users of this versatile business communication system. Download this comprehensive manual for free from our website and discover in-depth troubleshooting advice to maximize the performance and efficiency of your telecommunications infrastructure.

Share
Download
background image

Tools and Embedded Applications

Symptom

Probable Cause

Corrective Action

Callers are greeted by a

FAX tone instead of the

company greeting.

Programming error.

See “System Greetings”

and/or “RAD Greetings” in

the System Administration

Tool online help for

programming instructions.

Cannot modify voice

mailbox settings from the

Group Administration Tool.

Voice mailbox length and

directory number length are

different.

If the voice mailbox length

and directory number

length are different,

you can only edit voice

mailboxes from the System

Administration Tool or

the system Administrator

Mailbox.

Callers are transferred

to Auto Attendant when

pressing a Personal

Contact key.

An invalid phone number

was programmed.

Reprogram the Personal

Contact.

When an external trunk

is speed-dialed to the

embedded Auto Attendant,

the incoming caller

receives the wrong

greeting of “Please Enter

a Mail Box number”. The

Auto Attendant greeting

should be heard instead.

Improper options are

enabled in the Auto

Attendant's Class of

Service.

Set the following COS

options to either both “Yes”

or both “No”.

•

“Display ANI/DNIS/ISDN

Calling/Called Number”

•

“Display ANI/ISDN

Calling Number Only”

Document Version 1.0

215

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVoice Business 3300 ICP

JBL Authentics L8 Owner'S Manual preview
Authentics L8
Brand: JBL Pages: 16
JBL Authentics L 16 Owner'S Manual preview
Authentics L 16
Brand: JBL Pages: 17
Panamax M4000-PRO Instructions Manual preview
M4000-PRO
Brand: Panamax Pages: 16
Polycom EagleEye Director Quick Integration Manual preview
EagleEye Director
Brand: Polycom Pages: 13
Multilaser Royal P3159 User Manual preview
Royal P3159
Brand: Multilaser Pages: 25
Yealink MVC340-C4-000 Manual preview
MVC340-C4-000
Brand: Yealink Pages: 5
Sony CX-JN1 Service Manual preview
CX-JN1
Brand: Sony Pages: 74
Sony HCD-RG60 Service Manual preview
HCD-RG60
Brand: Sony Pages: 60
Sony HCD-RG555 Service Manual preview
HCD-RG555
Brand: Sony Pages: 70
Sanyo ECD-T1535 Owner'S Manual preview
ECD-T1535
Brand: Sanyo Pages: 16
Sanyo FXD-785GD Operating Instructions Manual preview
FXD-785GD
Brand: Sanyo Pages: 20
Sanyo FXD-888GD Operating Instructions Manual preview
FXD-888GD
Brand: Sanyo Pages: 28
Sanyo ECD-T1545 Operating Manual preview
ECD-T1545
Brand: Sanyo Pages: 32
Sanyo EP93F Brochure preview
EP93F
Brand: Sanyo Pages: 43
MAJORITY HNT-CDAB-BLK Instruction Manual preview
HNT-CDAB-BLK
Brand: MAJORITY Pages: 33
Sony MDR-HW300K Operating Instructions preview
MDR-HW300K
Brand: Sony Pages: 2
Sony MHC-C305 Operating Instructions Manual preview
MHC-C305
Brand: Sony Pages: 20
Sony MHC-C20 Operating Instructions Manual preview
MHC-C20
Brand: Sony Pages: 28

Brands by name

Popular brands

Load more brands