Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 178

Page: 178 / 366

Trunking

Symptom

Probable Cause

Corrective Action

DID call with number

in the name portion

fails to access Auto

Attendant directly.

Inbound ISDN calls

which present numbers

in the name portion

of the call will not

complete. The voice

mail which uses screen

scrapes are seeing the

numbers in the name

portion of the caller as

choice or extension

number, instead of a

trunk call, As a result,

the DID caller does not

hear the auto attendant

greeting and may

hear other voice mail

option or “please enter

your mailbox number

prompt”.

In the voice mail port's class of

service, set the following:

•

display ani/isdn calling number

only YES

•

display ani/dnis/isdn calling/

called number YES.

Document Version 1.0
Troubleshooting Guide

172

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands