Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 242

Page: 242 / 366

Voice Networking

Symptom

Possible

Cause

Corrective Action

For the 53xx phones, and for the 5540 console:

Press both volume keys at the same time,

release the volume-down key, dial 234

(“CFG”), then release the volume-up key to

display configuration options.

Press

to select

NETWORK PARAMETERS

press

to select

VIEW CURRENT VALUES

then press

to select

VIEW CURRENT

NETWORK

Press the volume-down key until

CUR

CONTROLLER IP

is displayed. This is the

address of the phone’s current ICP.

Press the volume-down key until

ICP1 IP

ADDRESS

is displayed. This is the address of

the phone’s primary ICP.

Toggle the volume keys (press the volume-

down and then volume-up key, or vice-

versa) to display

ICP2IP ADDRESS <IP

ADDRESS>

. This is the IP address of the

phone’s secondary ICP. Verify that this IP

address is correct. If the phone does not

display an IP address for a secondary ICP,

use the

User and Services Configuration

form in the

System and Administration Tool

provision the device with a secondary ICP.

Document Version 1.0
Troubleshooting Guide

236

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands