Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 213

Page: 213 / 366

Tools and Embedded Applications

Symptom

Probable Cause

Corrective Action

“Phantom” ringing occurs

when an ACD Hot Desk

Agent is logged into an

ACD.

The user profile for a hot

desk agent supports up to

47 programmable keys.

If an agent is assigned

47 feature keys and then

logs into an ACD hot desk

set that has fewer than

47 programmable keys

on it, the extra keys are

not accessible. If one of

these “inaccessible” keys

is programmed as a line

appearance, calls for the

line appearance will still

ring at the phone.

To avoid this problem,

choose one device

type that supports 13

programmable keys,

program a consistent

layout for the buttons, and

provide printed button

templates for each ACD

hot desk set.

Unable to log in to a 5560

IPT. Set display shows

“Login failed due to an

invalid dn”.

DNs for both the HDU

and the 5560 IPT are on

different ICPs/MiVoice

Business systems.

If the 5560 IPT is resilient,

the 5560 IPT and the hot

desk user DN must have

the same primary and

secondary.

Re-assign DNs so that the

5560 and HUD are on the

same system(s).

Device behaving incorrectly

after logging in with a 5560

IPT user profile. Display

continues to show previous

hot desk login and keys.

Attempts to log in again

results in “Login failed due

to a system error”

The device is NOT a 5560

IPT. Users of a 5560 IPT

can only hot desk into

another 5560 IPT.

Reboot the device to

restore in to normal

operation.

Document Version 1.0

207

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands