Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 187

Page: 187 / 366

Trunking

Symptom

Probable Cause

Corrective Action

Embedded MSDN/

DPNSS links are “not

seizable” and the red

LED is ON.

Faulty configuration or wiring.

Ensure that the T1/E1

cable is plugged into the

correct RJ-45 port on the

T1/E1 MMC.

Verify that the T1/E1 cable

is correctly wired. Note

that 1&2 and 4&5 are the

relevant pins for the cable.

Toggle the “Termination

Mode” setting in the Link

Descriptor Assignment

(either NT or LT). This

change takes about 15

seconds to take effect.

Embedded MSDN/

DPNSS links are “not

seizable” and the green

LED is ON.

Faulty configuration.

Ensure that the “Address

for Message Control”

field in the Digital Link

Descriptors form is set

appropriately (either “A” or

“B” depending on the far

end).

If the configuration is

correct, wait for about

1 minute until the every

circuit has finished

negotiating with the far

end.

High number of slips.

Incorrect configuration of

Network Synchronization form.

Ensure that the

synchronization source

being selected is to a

digital PSTN trunk (like PRI

or T1/D4).

Document Version 1.0

181

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands