Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 32

Page: 32 / 366

Initial Setup

Symptom

Possible Cause

Corrective Action

Unable to communicate

with the Application

Management Center

(AMC).

•

Inability to communicate

with the AMC because

unable to find the AMC

servers via a DNS

lookup.

•

Inability to communicate

with the AMC because

of network/system

configuration.

•

Inability to communicate

with the AMC using

specific protocols or

ports due to router or

firewall configuration

Refer to Mitel Knowledge

Base Article HO1318.

Cannot move licenses after

manual upgrade.

There is a specific

procedure that you must

follow to move licenses

after a manual upgrade.

Refer to Mitel

Knowledge Base Article

06-9999-00013.

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands