Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 318

Page: 318 / 366

Diagnosing Problems

Click the

Dial editor supports digits only

check box to enable the parameter.

Click

10.10 Trunks

Diagnosing Digital Trunk Issues

The following table lists key maintenance commands that you can use to diagnose

issues with digital trunks. Note that the following table does not provide a comprehensive

listing of all problems, but it does cover the most commonly encountered problems.

Table 61: Maintenance commands for diagnosing digital trunk issues

Symptom

Commands

Description

Any problem

edt show link config

all

edt show framer

config all

edt show link info

edt show vdsu table

These commands output generic

configuration information about the

embedded digital trunks. From the

output of these commands, you can

tell how the trunks are configured. Use

these commands to quickly identify any

differences between the perceived and

actual configuration of the trunks.

Document Version 1.0
Troubleshooting Guide

312

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands