Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 47

Page: 47 / 366

Hardware

•

In the System Administration Tool use the following Maintenance and Diagnostic forms:

•

Hardware Compute

form: displays details of the Real Time Controller (RTC) card and

Ethernet-to-TDM (E2T) card

•

Hardware Modules

form: displays the Mitel Mezzanine Card (MMC) modules that are

installed in the system.

•

IP Telephone

form: displays all IP phones in the system and their status.

•

For help with

diagnosing

hardware problems, see

Hardware

•

For help with

diagnosing

phone hardware problems, see

Phones

3.1 Hardware Alarms

Table 6: Hardware Alarms Troubleshooting

Alarm

Probable Cause

Corrective Action

E2T card has no IP

address.

If you are using the controller’s

internal DHCP server for the

E2T

: ensure you assigned a static

IP address to the E2T using the

correct MAC address (see “Configure

the Layer 2 Switch” in the “Initial

Setup” chapter or the

Technician’s

Handbook

for instructions).

If you

are using an external DHCP server

for the system:

verify that options

are programmed correctly (see

“Configuring External DHCP Settings

for E2T” in the “Installation Planner”

chapter of the Technician’s Handbook

for instructions).

ICP Comms

Incorrectly

programmed E2T IP

address or incorrect

setup of debug cable.

Verify that E2T parameters are

correct (see “Programming E2T

via Debug Cable or Secure Telnet”

section of the Technician’s Handbook

for instructions).

Document Version 1.0

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands