Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 217

Page: 217 / 366

Tools and Embedded Applications

•

Validate with the NG911 provider which number(s) they are expecting in the following

SIP headers:

•

PANI Header (information regarding the BSSID - provided by the WiFi Base

Stations)

•

FROM Header (CESID Information)

•

PAI - P-Asserted-Identity (CESID Information)

•

If the device originating the call has the capability to provide geolocation according

to RFC 6442, then the Geolocation header also applies.

•

If the integration with the NG911 requires so, verify that you have the correct values

configured in the SIP Peer profile:

•

User-Defined Header Name = E911-Organization-ID

•

User-Defined Header Value = Provided by the NG911 provider

•

Confirm which header is used by the NG911 provider to extract the CESID info (FROM

or PAI).

7.3.1.4 Next Steps

After you have gathered the information mentioned in the preceding section, proceed

with the following action plan:

Start a packet capture in the MiVB by using the Maintenance Command SIP

TCPDUMP ALL.

Make a test call (you can dial 911 or 933 for testing purposes).

Stop the packet capture in the MiVB by using the Maintenance Command SIP

TCPDUMP OFF.

Retrieve the WS_*.pcap file from the MiVB using sftp; the file is located under the

vmail directory.

Open the trace in wireshark.

Using the VoIP Calls option, locate the 911 or 933 call.

Click the first

INVITE

from MiVB.

Identify the headers/numbers listed in the preceding section.

Compare notes with the NG911 provider.

At this point, you have two possible options:

•

MiVB is sending the correct information:

•

Review the NG911 provider and correct the customer's info in the portal.

Document Version 1.0

211

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands