manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

The Mitel MiVoice Business 3300 ICP Troubleshooting Manual is an essential resource for users of this versatile business communication system. Download this comprehensive manual for free from our website and discover in-depth troubleshooting advice to maximize the performance and efficiency of your telecommunications infrastructure.

Share
Download
background image

Software

4.3.1 Recover the system through the Server Manager

1.

Log in to the Server Manager.

If you are unable to access or log in to the Server Manager, see 

Recover the System

through SSH

.

2.

After logging in to the Server Manager, verify whether the following error message is

displayed at the top of the page:

Detected several incomplete MiVoice Application reboots. The

MiVoice Business services are currently disabled. A manual

reboot is required after the root cause is addressed

You may collect the 

 journal

 log file(s) (

Administration > View log files

 ) to send to

Mitel Product Support for analysis.

3.

Swap the active partition of the controller with its inactive partition (

ServiceLink >

System Upgrade> Install and Upgrade > Swap to Inactive

 ).

4.

If the system is unable to boot the MiVoice Business software from its HDD after the

swap, see 

Unable to Recover the MiVoice Business system from Active and Inactive

Partitions

 .

5.

If the system is able to boot the MiVoice Business software after the swap, sync the

system licenses with the Application Management Center (AMC) server through the

Server Manager (

ServiceLink > Status

 ).

6.

After syncing system licenses with the AMC server, upgrade MiVoice Business to

the required software version through the Server Manager if needed (

ServiceLink >

System Upgrade

 ).

7.

Restore the most recent database using the Server Manager ( 

Administration >

Restore

).

4.3.2 Recover the System through SSH

Overview

If you are unable to log in to the Server Manager, then connect to the system through

SSH as root user (if SSH access is enabled), and use the following procedure to recover

the system. Please collect journal logs for product support for analysis.

Procedure

1.

Access the system through SSH (for example, through PuTTY) and log in as 

root

 .

If you are unable to access or log in to the system, see 

Recover the System through

the Maintenance Port

.

Document Version 1.0
Troubleshooting Guide

118

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVoice Business 3300 ICP

PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Brand: PACH & COMPANY Pages: 2
Absima CR9T Quick Start preview
CR9T
Brand: Absima Pages: 5
Jensen Marine MSR3012 Installation And Operation Manual preview
MSR3012
Brand: Jensen Marine Pages: 18
Lincoln Electric TOWN CAR Quick Reference Manual preview
TOWN CAR
Brand: Lincoln Electric Pages: 2
Discount Car Stereo A2DIY-VOL Quick Start Installation Manual preview
A2DIY-VOL
Brand: Discount Car Stereo Pages: 9
Sonoro SO-331 Operating Manual preview
SO-331
Brand: Sonoro Pages: 336
Commodore VY-VZ Installation Instructions Manual preview
VY-VZ
Brand: Commodore Pages: 18
Regintech SkypeConf User Manual preview
SkypeConf
Brand: Regintech Pages: 82
Danley SH-SM Owner'S Manual preview
SH-SM
Brand: Danley Pages: 8
Fender Passport Event Series 2 Owner'S Manual preview
Passport Event Series 2
Brand: Fender Pages: 44
Laser SPK-Q14PBD Instruction Manual preview
SPK-Q14PBD
Brand: Laser Pages: 1
MAJORITY HOMERTON 2 User Manual preview
HOMERTON 2
Brand: MAJORITY Pages: 26
btsr IS3 Operating Manual preview
IS3
Brand: btsr Pages: 71
BFT XPASS B 330/1200 L Instructions For Installation, Use And Maintenance Manual preview
XPASS B 330/1200 L
Brand: BFT Pages: 16
Boss Audio Systems 632UAB User Manual preview
632UAB
Brand: Boss Audio Systems Pages: 14
Mitsubishi Electric AT-50B Instruction Book preview
AT-50B
Brand: Mitsubishi Electric Pages: 68
Mitsubishi Electric AJ65VBTCU-68DAVN User Manual preview
AJ65VBTCU-68DAVN
Brand: Mitsubishi Electric Pages: 112
Mitsubishi Electric BAC-HD150 Instruction Book preview
BAC-HD150
Brand: Mitsubishi Electric Pages: 48

Brands by name

Popular brands

Load more brands