Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 125

Page: 125 / 366

Software

Run the following command to capture the system’s journal log into a file,

/ root/

journal.log

journalctl --no-pager > journal.log

. You may send

journal.log

to Mitel

Product Support for analysis.

Run the following command to initiate swap to the inactive partition:

perl -e "use esmith::util::inactive; print
esmith::util::inactive::swap();"

If the system is now able to boot the MiVoice Business software from its HDD, sync

the system licenses with the AMC server through the Server Manager (

ServiceLink >

Status

If the system is unable to boot the MiVoice Business software from its HDD after the

swap, see

Unable to Recover the MiVoice Business system from Active and Inactive

Partitions

After syncing system licenses with the AMC server, upgrade the MiVoice Business

system to the required software version through the Server Manager if needed (

ServiceLink > System Upgrade

Restore the most recent database using the Server Manager (

Administration >

Restore

4.3.3 Recover the System through the Maintenance Port

Overview

If you are unable to log in to the system through SSH, then you must access the system

console through the controller’s Maintenance port.

Before you begin

Ensure that you have access to the controller’s Maintenance port ( RS-232 port).

Procedure

Connect an RS-232 cable from the controller’s Maintenance port (

RS-232 port

) to

your maintenance PC’s serial port.

Document Version 1.0

119

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual, Page: 125 / 366

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews: