Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 69

Page: 69 / 366

Hardware

Phone

Symptom

Probable Cause

Corrective Action

Any

User reports

that they are

continually

receiving

incorrect calls.

System or set

programming error

Establish if the calls are

always for the same person

or if they are for different

people.

If the calls are always for

the same person check the

following:

•

Telephone Directory to

ensure that the name and

extension number are

correct.

•

The users number against

that of the person people

are looking for. If the

numbers are similar then

it is possible that people

are dialing incorrectly.

Changing the users

extension number maybe

an option.

•

That the person being

called has not call

forwarded or rerouted calls

to the user (who raised the

complaint) in error.

If the calls are for different

people try these options:

•

Ask the user to log the

calls received in Error.

•

Check the SMDR logs to

establish a pattern.

Document Version 1.0

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands