Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 95

Page: 95 / 366

Hardware

Error Message

on Display

Possible

Cause

Corrective Action

DHCP Discovery

DHCP OFFER X

REJ

(VLAN) (after

releasing the first

IP from the native

DHCP server)

DHCP Option 43

or 125 on 3300

Release 7.0 or

later systems or

Option 30 (MITEL

IP PHONE) for

earlier Releases

is not program-

med on the

second scope of

the DHCP server

(or on the second

DHCP server).

VLAN ID is not

assigned properly.

Identify if there is one DHCP server for

both VLANs, or if there is one DHCP server

per VLAN (see “Network Configuration

Examples” in the “Typical Network

Configurations” chapter of the

Technician’s

Handbook

For one DHCP server for both VLANs,

ensure that option 43 or 125 is properly

configured (3300 Release 7.0 and later)

or that option 130 is programmed as

String type with value of “MITEL IP

PHONE“ (prior to Release 7.0), in the

scope of Voice LAN.

For one DHCP server per VLAN, ensure

that option 43 or 125 (Release 7.0 and

later) or 130 (prior to Release 7.0) is

defined.

Verify that the proper VLAN ID is assigned

in option 43 or 125 (Release 7.0 and later),

or 132 (prior to Release 7.0).

One DHCP

server for two

VLANs network

configuration: IP

helper address

on the router

interface is not set

up correctly.

On the router interface (on which DHCP is

not residing), enter the IP helper address

and specify the IP address of the DHCP

server on the other side of the subnet (that

is, always set up IP helper address on the

DHCP server client side).

Ensure the second scope is created for

the corresponding VLAN (see “Network

Configuration Examples” in the “Typical

Network Configurations” chapter of the

Technician’s Handbook

Document Version 1.0

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands