manualshive.com logo in svg

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

The Mitel MiVoice Business 3300 ICP Troubleshooting Manual is an essential resource for users of this versatile business communication system. Download this comprehensive manual for free from our website and discover in-depth troubleshooting advice to maximize the performance and efficiency of your telecommunications infrastructure.

Share
Download
background image

Hardware

Symptom

Probable

Cause

Corrective Action

Faulty power

connections.

Verify the following:

•

Ensure power is applied to the power unit.

•

Ensure you are not using crossover Ethernet

cables.

•

Ensure that the input Ethernet cable is connected

to the Data In port of the power unit.

•

Ensure that the output Ethernet cable is

connected to the Data and Power Out port of the

power unit.

•

Ensure that the input and output cables of a port

pair are used for the same IP Phone.

IP device

does not work,

and both

Port Status

LEDs are OFF

(Power unit is

not detecting

IP device).

Wiring

problem

OR

faulty IP

device

OR

faulty Power

Unit.

1.

Verify you are using a standard UTP Category 5, 6

or 6e cable (with 8 wires–4 pairs).

2.

Verify that you are not using a crossover cable.

3.

Verify that the connections for the port pair both

correspond to the same IP device, and that the

port connections are not reversed.

4.

Verify that the cables connected to the Data In

and Data Out ports correspond to the same IP

device.

5.

Connect the IP device to a different port pair on

the Power Unit. If the device works normally, the

original port is probably faulty.

6.

Connect the IP device directly to the Power Unit

using a short cable. If the device works normally,

the original cable (or one of its connectors) is

faulty.

7.

If possible, connect the IP device to a different

Power Unit. If the device works normally, the

original Power Unit is probably faulty.

Document Version 1.0

83

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVoice Business 3300 ICP

KAR-TECH MICRO Installation And Operation Manual preview
MICRO
Brand: KAR-TECH Pages: 28
JBL Soundgear Series Service Manual preview
Soundgear Series
Brand: JBL Pages: 73
Polycom 1725-15849-001 Quick Start Manual preview
1725-15849-001
Brand: Polycom Pages: 2
ClearOne magicbox aavelin User Manual preview
magicbox aavelin
Brand: ClearOne Pages: 93
Magnetic Autocontrol MHTM Operating Instructions Manual preview
MHTM
Brand: Magnetic Autocontrol Pages: 132
Steelcase media:scape mini Manual preview
media:scape mini
Brand: Steelcase Pages: 7
Gecko Aeware in.k100 Series User Manual preview
Aeware in.k100 Series
Brand: Gecko Pages: 10
dB Technologies RW 16MS/BS Quick Start User Manual preview
RW 16MS/BS
Brand: dB Technologies Pages: 2
NEC CONFERENCE MAX NDA-31109 User Manual preview
CONFERENCE MAX NDA-31109
Brand: NEC Pages: 5
Dell C7017T User Manual preview
C7017T
Brand: Dell Pages: 67
VIA Technologies ARTiGO-A600 Development Manual preview
ARTiGO-A600
Brand: VIA Technologies Pages: 56
Halytech Illuminator Quick Start Manual preview
Illuminator
Brand: Halytech Pages: 2
ZANDER Multitronic Installation Manuallines preview
Multitronic
Brand: ZANDER Pages: 16
Hamilton Air HA1000 Adjustment Instructions preview
HA1000
Brand: Hamilton Air Pages: 3
GRASS VALLEY Encore Configuration Manual preview
Encore
Brand: GRASS VALLEY Pages: 426
Mitel UC360 Installation Manual preview
UC360
Brand: Mitel Pages: 8
Ednet 83173 Manual preview
83173
Brand: Ednet Pages: 4
ESA RC-900 Manual preview
RC-900
Brand: ESA Pages: 8

Brands by name

Popular brands

Load more brands