Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 321

Page: 321 / 366

Diagnosing Problems

Symptom

Commands

Description

Call problems

are generating

message output

that you need to

capture in a file for

interpretation

edt enable logtofile

(turns on message

tracing)

edt disable logtofile

(turns off message

tracing)

This command puts all of the traces

turned on by “edt trace …” into the “/db/

LDS_Trace.rtf” file (DigTrkTrace prior to

3300 Rls 6.1).

If you need to enable tracing on a busy

switch, you should send the output to the

trace file because the output to the

response window is slow and can impact

the performance of the 3300 ICP

This log file must be interpreted by Mitel

designers. It is not meant to be interpreted

by customers or field technicians.

T1/E1 module

(embedded PRI)

issues

All ESM digital

trunk maintenance

commands

available to the

NSU apply to the

T1/E1 module

and can be

entered through

the Maintenance

commands form

of the System

Administration Tool.

Refer to Mitel Knowledge Base article

04-5191-00014

10.11 Hardware

Using LEDs to Diagnose Faults

Controllers, units, modules and cards have light-emitting diodes (LEDs) that indicate their

current status. Refer to the Technician's Handbook for tables that list the LED states and

the meaning of each state.

•

Reading E2T Card Statistics

on page 316

•

Diagnosing DSP Module Related Issues

on page 318

Document Version 1.0

315

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands