Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 177

Page: 177 / 366

Trunking

Symptom

Probable Cause

Corrective Action

Q.Sig Private network

access is enabled in

PRI link descriptor.

For the link descriptor assignment

used by the PRI link, set “Q.Sig

Private network access” to NO.

(This option should not be enabled

for normal PRI. It should only be set

if the link is intended for Q.Sig.)

After you install or

initially program an

embedded E1 module,

the DASS II link does

not work.

In the Link Descriptor

Assignment for the

DASS II link, the

CRC-4 is set to “Yes”.

In the Link Descriptor Assignment

for the DASS link, set the CRC-4

setting to “No” and then reset

the controller. If you alter the

CRC-4 setting, you MUST reset

the controller to enable the new, or

changed, setting.

Cannot dial

international numbers

when connected

to DMS500 switch

running DMS100

protocol.

System is connected

to a DMS500 switch

running DMS100

NI1 protocol and the

service provider has an

NI2 table programmed

in the central office.

The protocol may set

correctly in the central

office; however the NI2

table should not be

programmed.

Refer to Mitel Knowledge Base

article 05-5107-00005.

Document Version 1.0

171

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands