Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 218

Page: 218 / 366

Tools and Embedded Applications

•

MiVB is NOT sending the right information:

•

Review CESID configuration and refer to the

MiVoice Business RAY BAUM'S Act

Solution Deployment Guide.

for more information

Ensure that there are sufficient SIP trunk licenses are available. Refer to the

MiVoice

Business Red Sky Deployment Guide

for more information.

7.4 Embedded Voice Mail

Table 37: Embedded Voice Mail

Symptom

Probable Cause

Corrective Action

After upgrading from 8.0,

the embedded voice mail

fails to start.

Monitoring the journalctl

logs you will see the

following:

Starting iPVM Version

9.2.1.4

*** Fatal error starting the

voice driver.

iPVM stopped.

Voice Mail Did not start

Successfully

Obsolete DSP (Quad DSP

21061) installed.

Replace with a Quad

21161 or DSP II depending

on the platform and

function they are being

used for.

Notification is not enabled

at the system level.

Enable notification in VM

Options form.

Notification calls are

configured for a mailbox

but don't seem to work.

CO line access is restricted

for voice mail port

extension numbers.

Ensure that voice mail port

numbers are not restricted

from access to CO lines.

Document Version 1.0
Troubleshooting Guide

212

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands