Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 111

Page: 111 / 366

Hardware

Symptom

Possible Cause

Corrective Action

Audio issues

on SIP,

including Music

on Hold.

Need to have

ENABLE_TX_CHAN_CONN

feature enabled.

3.5 5550 IP Console

Table 17: 5550 IP Console Problems Troubleshooting

Symptoms

Probable cause

Corrective Action

TKB (keyboard) - does

not have a reserved IP

address

does not have the right

IP address

is not communicating

with the right controller.

Check DHCP lease to confirm

if an expected IP address is

assigned to TKB.

If not assigned properly,

ensure that you enter the MAC

address of TKB properly in the

Multiline Sets form in System

Administration Tool.

Recycle the power of the

TKB to ensure that the TKB is

reloaded properly.

5550 IP console fails to

on TKB).

Console PC does not

have the proper IP

address.

If the IP address of PC is on

different subnet than the TKB,

make sure that the router

between these two subnets is

functional.

Document Version 1.0

105

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands