Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 93

Page: 93 / 366

Hardware

Table 14: IP Phone Registration Troubleshooting

Error Message

on Display

Possible

Cause

Corrective Action

Invalid VLAN ID

DHCP Option 43

or 125 on 3300

Release 7.0 or

later systems

or 132 and/or

133 for earlier

releases not set

correctly.

Identify the location of DHCP server and

which DHCP server is assigned the IP

address for the corresponding subnet (see

“Network Configuration Examples” in the

“Typical Network Configurations” chapter of

the

Technician’s Handbook

for examples).

For an external Microsoft DHCP server

(NT server, etc.), make sure that the option

type is set to LONG.

For a Cisco

Router DHCP server, make

sure that the option type is set to hex, and

padded with 0s (for example, 0x00000002

for VLAN 2).

For the controller internal DHCP server, set

the option type to numeric.

Existing data

device owns the

IP address.

Check the IP address on the phone

display.

Disconnect the IP Phone.

From a PC on the same subnet, ping the

suspected IP Phone. If there is a response,

identify the data device, and resolve the

conflict.

D uplicated IP

address

Corrupted DHCP

server.

On the suspected DHCP server, disable

then recreate the scope.

If this is a Microsoft DHCP server, reboot

the server.

Document Version 1.0

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands