Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 161

Page: 161 / 366

System Features

Feature

Symptom

Probable Cause Corrective

Action

Speaking too

quietly

Speak at a normal

volume towards the

microphone.

Hold

User unable to

place DID On-Hold.

Users unable to

put DID calls on

hold when the

COS of the set has

Record-A-Call -

Save Recording on

Hang-up enabled.

Disable “Record-

A-Call - Save

Recording on Hang-

up” option in the

COS of the set.

Incorrect “Hunt

Group Mode”

specified.

Ensure that the

desired Hunt Group

Mode (Circular

or Terminal) is

specified in the

Hunt Groups form.

Hunt Groups

Calls not ringing

sets in expected

order.

Hunt group

members are

programmed in the

wrong order in the

Hunt Groups form.

Ensure that the

member directory

numbers are

entered (listed) in

the Hunt Groups

form in the order

that you want the

calls distributed.

Document Version 1.0

155

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands