Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 226

Page: 226 / 366

Tools and Embedded Applications

Symptom

Probable Cause

Corrective Action

ALL Visual Voice Mail

users get the following

response when they try to

access a message.

“NO AUDIO

CONNECTION”

Either Hunt group is not

programmed in "Voice

Mailboxes" form.Or

All ports are busy.

Ensure that the Hunt group

is programmed in the Voice

Mailboxes form.

As all voice mail ports are

busy so Program more

voice mail ports/ try after

sometime.

Telephone only rings once

Call transfer fails.

Supervised transfer timed

out.

In the ESM VM Options

form, disable the

“Supervised Transfer”

option.

Default value of "Transfer

Ringback timeout" is 17

seconds now.

Minor Alarm is raised.

Not enough DSP

Resources available.

Add DSP resources.

See “Increasing DSP

Resources” in the

“Installation Planner”

chapter of the

Technician’s

Handbook

Sent time is wrong on e-

mails forwarded from voice

mail.

Time Zone not set correctly

in Voice Mail programming.

In the ESM VM Network

Servers form, program the

“Time Zone” field.

Message waiting lamp is

on but there is no message

in your mailbox.

Multiple possible causes.

Request to off MWI is

failed as all ports were

busy.Message Waiting

Activate/ Deactivate

Programming is wrong.

Program more VM ports to

avoid this issue.Get ESM

help to program Message

Waiting Deactivate code.

Document Version 1.0
Troubleshooting Guide

220

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands