Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 102

Page: 102 / 366

Hardware

Symptom

Possible Cause

Corrective Action

Cannot make call

over analog loop trunk

(intermittent problem).

PBX is sending the dialing

digits too fast for Telco's

receiver on the LOOP

trunk.

Insert a tone plan in the

ARS Digit Modification

Plans for the route used

by analog loop trunk (tone

plan is used to insert one

or two seconds delay

without any tone detection).

NONE of the sets are

responding.

Problem with controller.

Perform a system check on

the controller.

Sets cannot receive DID

calls.

Non-DID is enabled in

Station Attributes form.

Disable non-DID in the

set's COS.

Set is not programmed.

In System Administration

Tool, program the

extension accordingly.

Wrong wiring.

Check the wiring between

the phone jack and the

ASU, ASU II, AMB, or

AOB.

Faulty handset wire.

Replace the handset

cord.

Replace the handset.

Replace the set.

No dial tone on set.

Circuit is busy.

Enter the Maintenance

command STATE <plid

of the circuit>.

Enter the Maintenance

command RTS <plid>.

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands