Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 36

Page: 36 / 366

Initial Setup

Setup Verification

Confirm that IP address

of test PC is in the same

subnet of 3300.

Go to DOS prompt of

PC, issue ipconfig / all

Verify the gateway

address/DNS setting of

test PC is identical to

3300.

In ESM, verify subnet,

gateway and DNS

setting in the system IP

properties.

Test Action

Launch a command

prompt and perform the

following action1a ping

ping sync.mitel-amc.com

If the test PC does not

have the same subnet,

gateway and DNS

settings, correct them

to meet the customer

network’s requirement.

If ping test fails,

•

Verify if DNS setting

is correct.

Note

The ping test may fail

due to “Echo Reply”

may be blocked by

the firewall. If the

ping test fails due to

the blocking of Echo

reply by Firewall, one

should proceed with

Step 2.

•

You must verify

DNS is correct.

Note

The current IPs

used by AMC are

216.191.234.90 and

216.191.234.91. You

must use DNS for

connectivity. Mitel

reserves the right to

change IP address

scheme without

notification,

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands