Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 52

Page: 52 / 366

Hardware

3.2 Controllers

MXe III/MXe III-L Controller
Table 7: MXe III Controller Troubleshooting

Symptom

Probable

Cause

Corrective Action

Changing

from a hard

coded E2T

IP address

to requesting

one from the

DHCP server.

(If

any

addresses

remain on the

E2T (at “inet

on ethernet”,

“host inet”,

or “gateway

inet”), the

E2T will use

them and

will obtain

the rest of its

parameters

from the

DHCP

server.)

For information and guidance for correcting this

problem, refer to "Programming E2T via Debug Cable

or Secure Telnet" in the

Technician’s Handbook

E2T fails to

initialize.

RTC is set

up with a

different

virtual LAN

(vlan).

From the RTC shell or the E2T VxWorks shell, remove

the vlan using the

command.

Document Version 1.0
Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands