Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 123

Page: 123 / 366

Software

Software on a 3300 ICP Controller (Manually)

in the

MiVoice Business Technician's

Handbook

If any of the parameters needs to be modified, modify their values as follows:

Run the following command to modify the U-Boot configuration file values.

run ubootcfg

Update the relevant parameter as needed.

10.

Without resetting the system, run the following command to save the updated U-Boot

variables from RAM to FLASH.

saveenv

Now you should be able to initiate the full manual full installation of your ICP3300

Controller.

4.3 Unable to boot the MiVoice Business System on 3300 ICP

Controller

Overview

You must

Recover the system through the Server Manager

if:

•

the MiVoice Business software is unable to boot from the HDD (or SSD) of your 3300

ICP Controller.

•

the MiVoice Business application fails to boot several times. In this case, the error

message

Detected several incomplete MiVoice Application reboots.

The MiVoice Business services are currently disabled. A manual

reboot is required after the root cause is addressed

is displayed.

•

Recover the system through the Server Manager

on page 118

•

Recover the System through SSH

on page 118

•

Recover the System through the Maintenance Port

on page 119

•

Password Recovery for 3300 ICP Controller

on page 121

•

Unable to Recover the MiVoice Business System from Active and Inactive Partitions

on page 123

Document Version 1.0

117

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands