Mitel MiVoice Business 3300 ICP Troubleshooting Manual Download Page 127

Page: 127 / 366

Software

Run the following command to initiate swap to the inactive partition:

perl -e "use esmith::util::inactive; print
esmith::util::inactive::swap();"

If the system is now able to boot the MiVoice Business software from its HDD, sync

the system licenses with the AMC server through the Server Manager (

ServiceLink >

Status

If the system is unable to boot the MiVoice Business software from its HDD after the

swap, see

Unable to Recover the MiVoice Business System from Active and Inactive

Partitions

on page 123.

After syncing system licenses with the AMC server, upgrade the MiVoice Business

system to the required software version through the Server Manager if needed (

ServiceLink > System Upgrade

Restore the most recent database using the Server Manager (

Administration >

Restore

4.3.4 Password Recovery for 3300 ICP Controller

Overview

If you are unable to log in to the Server Manager or the system (SSH or the Maintenance

port), then you must perform a password recovery.

Before you Begin

Ensure that you do the following:

•

Verify that you have access to the Maintenance port (

RS-232 port

•

Verify that the controller is powered on.

Procedure

Note

The system will be offline for the entire duration of the following procedure.

Connect an RS-232 cable from the controller’s Maintenance port (

RS-232 port

) to

your maintenance PC’s serial port.

Document Version 1.0

121

Troubleshooting Guide

Summary of Contents for MiVoice Business 3300 ICP















































































































































































































































































































































































Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands

Mitel MiVoice Business 3300 ICP, Troubleshooting Manual

Search results

Summary of Contents for MiVoice Business 3300 ICP

Reviews:

Related manuals for MiVoice Business 3300 ICP

Brands by name

Popular brands