Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 205

Page: 205 / 313

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• See “

Parts listing - BladeCenter HX5

” on page 57 to determine which components are CRUs and which

components are FRUs.

• If an action step is preceded by “(Trained service technician only),” that step must be performed only by a

trained service technician.

Type

Error Message

Action

Information

System mgmt software (Scale
Config) software change detected

Information only; no action is required.

Note:

This event is not be displayed in the advanced

management module event log. However, it is sent for alerts
and SNMP traps.

Error Code: 0x806F0129

Error

PCI express bus 3, battery (SAS DC
Batt) failed

1. Reseat the battery for the storage interface card.

2. Replace the battery for the storage interface card.

Error Code: 0x806F0207

Note:

Multiple events can be displayed for this error code. Be sure to read the message text to determine the

appropriate recovery actions.

Error

Group 4, processor (One of CPUs)
BIST failure

1. Remove the blade server and ensure the processors are

installed correctly (see “Installing a microprocessor and
heat sink” on page 134).

2. Verify that the system is running the latest UEFI firmware

(see “Updating firmware and device drivers” on page 30).

3. Run the Setup utility (see “Using the Setup utility” on page

20).

a. Make sure that both processors are displayed by the

system.

b. Load the default settings.

c. Go to the

System Settings

menu and make sure the

processor is enabled.

4. (Trained service technician only) Replace the processor

(see “Removing a microprocessor and heat sink” on page
130 and “Installing a microprocessor and heat sink” on
page 134).

5. (Trained service technician only) Replace the system-

board assembly (see “Removing the system-board
assembly - BladeCenter HX5” on page 140 and “Installing
the system-board assembly - BladeCenter HX5” on page
142).

Chapter 5

Diagnostics

189

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands