Lenovo BladeCenter HX5 1909 Problem Determination And Service Manual Download Page 66

Page: 66 / 313

Step 11. Copy the downloaded firmware update package into a directory.

Step 12. From a command line, type

filename

-s

, where

filename

is the name of the executable file that you

downloaded with the firmware update package.

Step 13. Reboot the server and verify that it completes POST (see “Turning off the blade server” on page 12

and “Turning on the blade server” on page 11).

Step 14. Turn off the server (see “Turning off the blade server” on page 12).

Step 15. Remove the blade server form the BladeCenter unit (see “Removing the blade server from the

BladeCenter chassis” on page 66).

Step 16. Remove the server cover. See “Removing the blade server cover” on page 71.

Step 17. Move the UEFI boot block recovery switch (SW2-7) to the OFF position (see “System-board

switches” on page 13).

Step 18. Replace the cover and reinstall the blade server in the BladeCenter unit, making sure that the media

tray is selected by the relevant blade server. See “Installing the blade server cover” on page 73 and
“Installing a blade server in a BladeCenter chassis” on page 67.

Step 19. Restart the blade server (see “Turning off the blade server” on page 12 and “Turning on the blade

server” on page 11). The system begins the power-on self-test (POST).If this does not recover the
primary bank continue with the following steps.

Step 20. Remove the blade server form the BladeCenter unit (see “Removing the blade server from the

BladeCenter chassis” on page 66).

Step 21. Remove the server cover. See “Removing the blade server cover” on page 71.

Step 22. Reset the CMOS by removing the battery (see “Removing the battery” on page 76).

Step 23. Leave the battery out of the server for 5 minutes.

Step 24. Reinstall the battery (see “Installing the battery” on page 77).

Step 25. Replace the cover and reinstall the blade server in the BladeCenter unit, making sure that the media

tray is selected by the relevant blade server. See “Installing the blade server cover” on page 73 and
“Installing a blade server in a BladeCenter chassis” on page 67.

Step 26. Restart the blade server (see “Turning on the blade server” on page 11).

The system begins the power-on self-test (POST).

Out-of-band manual recovery method

To recover the server firmware and restore the server operation to the primary bank, complete the following
steps:

Step 1. Download the blade server UEFI firmware update from the World Wide Web (see “Updating

firmware and device drivers” on page 30).

Step 2. Turn off the server (see “Turning off the blade server” on page 12).

Step 3. Remove the blade server from the BladeCenter unit (see “Removing the blade server from the

BladeCenter chassis” on page 66).

Step 4. Remove the server cover. See “Removing the blade server cover” on page 71 for more information.

Step 5. Locate the UEFI boot block recovery switch (SW2-7) on the system board (see “System-board

switches” on page 13).

Step 6. Use your finger to move switch SW2-7 to the ON position.

Step 7. Replace the cover and reinstall the blade server in the BladeCenter unit, making sure that the media

tray is selected by the relevant blade server. See “Installing the blade server cover” on page 73 and
“Installing a blade server in a BladeCenter chassis” on page 67.

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Search results

Summary of Contents for BladeCenter HX5 1909

Reviews:

Related manuals for BladeCenter HX5 1909

Brands by name

Popular brands