manualshive.com logo in svg

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Introducing the Lenovo BladeCenter HX5 1909, a high-performance server built for efficiency and reliability. Need assistance with troubleshooting or servicing? Look no further! Download the Problem Determination And Service Manual for free, exclusively from manualshive.com. Get the help you need to optimize your Lenovo BladeCenter HX5 1909's performance today!

Share
Download
background image

Switch number

Description

Switch setting

Definition

SW2 - 1

Reserved

SW2 - 2

Force power on

The default position is off.

Turning this switch to the on 
position forces the blade 
server to power on

SW2 - 3

Trusted Platform Module 
(TPM) physical presence

The default position is off. 

Turning this switch to the on 
position indicates a physical 
presence to the TPM.

SW2 - 4

Password override switch

The default position is off.

Turn this switch to the on 
position overrides the power 
on password. 

SW2 - 5

Real time clock (RTC) reset

The default position is off.

Turning this switch to the on 
position resets the RTC. A 
momentary toggle is all that 
is required. To avoid 
excessive battery drain, do 
not leave this switch on.

SW2 - 6

Reserved

SW2 - 7

Flash bank select

The default position is off.

Turning this switch to the on 
position forces the blade to 
boot from the backup UEFI 
image.

SW2 - 8

Wake on LAN (WOL) disable

The default position is off. 

Turning this switch to the on 
position disables WOL.

SW2 - 9

Force H8 update

The default position is off.

N/A

SW2-10

Reserved

Blade server connectors - IBM MAX5

Use this information to locate the IBM MAX5 expansion blade connectors.

The following illustration shows the system board components, including connectors for user-installable 
optional devices, in the IBM MAX5 expansion blade.

14

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

D-Link ShareCenter Pro DNS-1200-05 Quick Installation Manual preview
ShareCenter Pro DNS-1200-05
Brand: D-Link Pages: 68
IBM eserver xSeries 440 Quick Reference preview
eserver xSeries 440
Brand: IBM Pages: 34
Supermicro SuperWorkstation 740A-T User Manual preview
SuperWorkstation 740A-T
Brand: Supermicro Pages: 138
HPE ProLiant DL580 Gen10 User Manual preview
ProLiant DL580 Gen10
Brand: HPE Pages: 158
Supero SUPERSERVER 6015C-M3 User Manual preview
SUPERSERVER 6015C-M3
Brand: Supero Pages: 118
TYAN B3970-U Service Engineer'S Manual preview
B3970-U
Brand: TYAN Pages: 77
Discover Video Devos 4 User Manual preview
Devos 4
Brand: Discover Video Pages: 148
Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual preview
PRIMERGY CX400 M6
Brand: Fujitsu Pages: 209
Fujitsu PRIMERGY CX272 S1 Upgrade And Maintenance Manual preview
PRIMERGY CX272 S1
Brand: Fujitsu Pages: 234
Fujitsu Primergy CX270 S2 Upgrade And Maintenance Manual preview
Primergy CX270 S2
Brand: Fujitsu Pages: 320
Fujitsu Primergy CX270 S2 Operating Manual preview
Primergy CX270 S2
Brand: Fujitsu Pages: 56
D-Link DPR-2000 Quick Installation Manual preview
DPR-2000
Brand: D-Link Pages: 40
Blue Arc Titan SiliconServer System Administration Manual preview
Titan SiliconServer
Brand: Blue Arc Pages: 487
G-Technology G-RAID Studio Product Manual preview
G-RAID Studio
Brand: G-Technology Pages: 50
Planet FPS-1PW User Manual preview
FPS-1PW
Brand: Planet Pages: 87
Viavi G4-40G-100-384T Manual preview
G4-40G-100-384T
Brand: Viavi Pages: 12
Sugon I620-G20 User Manual preview
I620-G20
Brand: Sugon Pages: 155
360 Systems MAXX-1200-EX Operation Manual preview
MAXX-1200-EX
Brand: 360 Systems Pages: 148

Brands by name

Popular brands

Load more brands