manualshive.com logo in svg

Lenovo BladeCenter HX5 1909, Problem Determination And Service Manual

Introducing the Lenovo BladeCenter HX5 1909, a high-performance server built for efficiency and reliability. Need assistance with troubleshooting or servicing? Look no further! Download the Problem Determination And Service Manual for free, exclusively from manualshive.com. Get the help you need to optimize your Lenovo BladeCenter HX5 1909's performance today!

Share
Download
background image

Step 5.  If an optional expansion unit is installed, remove the expansion unit (see “Removing an expansion 

unit” on page 96 for instructions). 

Note: 

Optional expansion units are not supported when a IBM MAX5 expansion blade is installed.

Step 6.  If an IBM MAX5 expansion blade is installed, remove it (see “Removing an IBM MAX5 expansion 

blade” on page 87 for instructions).

Step 7.  Open the blade server cover (see “Removing the blade server cover” on page 71 for instructions).

Step 8.  If a CFFh expansion card is installed, remove it (see “Removing a CFFh expansion card” on page 

119 for instructions).

Step 9.  Insert the back of the SSD expansion card into the expansion-card standoffs on the blade server 

and rotate the expansion card down toward the system board. 

Note: 

The expansion card standoff in the middle of the blade server has two slots. The top slot is 

for the CFFh expansion card. Be sure to insert the SSD expansion card into the bottom slot of the 
expansion-card standoff that is located in the middle of the blade server.

Step 10.  Carefully push down on the SSD expansion card (pressing on the blue label) until the expansion 

card is seated. 

Note: 

Make sure that the expansion card lever is in the closed position.

Expansion
card

Expansion
card
standoff

Expansion
card
standoff

Step 11.  Install the CFFh expansion card, if you removed one from the blade server (see “Installing a CFFh 

expansion card” on page 122 for instructions).

Step 12.  If the blade server is part of a scalable blade complex, assemble the scalable blade complex (see 

“Assembling a scalable blade complex” on page 70 for instructions).

Step 13.  Install the IBM MAX5 expansion blade if you removed one (see “Installing an IBM MAX5 expansion 

blade” on page 88 for instructions).

Step 14.  Install the optional expansion unit, if you removed one from the blade server (see “Installing an 

expansion unit” on page 97 for instructions).

Step 15.  Install the cover onto the blade server (see “Installing the blade server cover” on page 73 for 

instructions).

Step 16.  Install the blade server or scalable blade complex into the BladeCenter chassis (see “Installing a 

blade server in a BladeCenter chassis” on page 67 for instructions).

100

BladeCenter HX5 Blade ServerProblem Determination and Service Guide

Summary of Contents for BladeCenter HX5 1909


























































































































































































































































































































Reviews:

No comments

Related manuals for BladeCenter HX5 1909

GarrettCom Magnum 10ETS Hardware Installation And User'S Manual preview
Magnum 10ETS
Brand: GarrettCom Pages: 55
Inspur NF5260FM6 User Manual preview
NF5260FM6
Brand: Inspur Pages: 82
Fujitsu Siemens Computers PRIMERGY B120 Operating Manual preview
PRIMERGY B120
Brand: Fujitsu Siemens Computers Pages: 68
Sun Microsystems iPlanet Web Server Installation Manual preview
iPlanet Web Server
Brand: Sun Microsystems Pages: 62
IBM totalstorage fastt100 Installation, User And Maintenance Manual preview
totalstorage fastt100
Brand: IBM Pages: 160
IBM System x3550 M3 Installation And User Manual preview
System x3550 M3
Brand: IBM Pages: 160
IBM System x3650 M4 Type 7915 Installation And User Manual preview
System x3650 M4 Type 7915
Brand: IBM Pages: 192
IBM x3750 M4 Installation And Service Manual preview
x3750 M4
Brand: IBM Pages: 694
IBM System x3755 M3 7164 Installation And User Manual preview
System x3755 M3 7164
Brand: IBM Pages: 126
Zonet ZUH2000 - Product Data preview
ZUH2000 -
Brand: Zonet Pages: 2
netAlly Test Accessory User Manual preview
Test Accessory
Brand: netAlly Pages: 2
Planet FPS-3121G User Manual preview
FPS-3121G
Brand: Planet Pages: 74
Polycom KIRK 500 User Manual preview
KIRK 500
Brand: Polycom Pages: 34
Black Box Terminal Server User Manual preview
Terminal Server
Brand: Black Box Pages: 131
VBrick Systems EtherneTV User Manual preview
EtherneTV
Brand: VBrick Systems Pages: 44
W&T 53641 Manual preview
53641
Brand: W&T Pages: 79
Adaptec 5325301507 - Snap Server 4400 NAS Administrator'S Manual preview
5325301507 - Snap Server 4400 NAS
Brand: Adaptec Pages: 250
B+B SmartWorx VESR424D Quick Start Manual preview
VESR424D
Brand: B+B SmartWorx Pages: 2

Brands by name

Popular brands

Load more brands